Monday, 7 November 2011

TTEC4842- AUTOMOTIVE ENGINES (Cooling system)

      TTEC4842- AUTOMOTIVE ENGINES (cooling system) 

                     ENGINES- Cooling system



                                         


Important: while carrying out the tasks to check the cooling systems remember the engine may be moving parts that could injure if your hands or other body parts come into contact with them.
Safety: 
  • Hot metal parts of the system can burn.
  • Hot water and steam scalds and burns.
  • The cooling system is under pressure when hot.
  • Injury from moving parts of the engine.
  • Corrosion and anti freeze splkashes in the eyes.
  • Personal injury from hand tools.

Indirect cooling: To complete this practical task  we need an indirect (liquid) cooled engine that is complete and working.
Here we learn how to check the radiator visually for security of the mounts. when we checked the radiator core for corrosion , we rubbed the hand gently over fins and see if they are flaking off.
and for leaks at the top and bottom of the tank were seen by detection of  stains or white powdery deposits along tank seams.

REPORT: Hoses were in good condition, no leaks around the cap & no leaks n damage to top & bottom tank, condition of fins n tubes not much good.

CHECKING COOLANT  ANTIFREEZE SPECIFIC GRAVITY:Engine coolant should have a antifreez & a corrossion inhibitor in it. Then we checked ratio of the coolant mix usingcooling system hydrometer.

My Reading was: 10%
Which was out of manufacturers spec., n most spec are 50%


Q.Then we were asked 'If the capacity of the cooling system is 8 litres, then what action needs to be taken in bring the coolant to manufacturer's specifications?
= So as our result is 10% , so 90% is my water that means 7.2L water is inside radiator so we need to take out 3.2L of water and add  3.2L of coolant to make it 50% of water & 50% of coolant.


CHECKING RADIATOR HOSES:Here we learn to check the radiator hoses, which can be seem quite serviceable from outside, but perished on the inside .
then we checked it for the internal flaking, oil soaked or swollen , and hard and cracking.


other faults check:

                                     TOP hose         Bottom hose 

Hardening                      ok                       ok                                       

Cracks                            ok                      ok                                    
Internal flaking             ok                       ok                                             
Chaffed or burned        ok                      ok                                          
oil soaked or swollen     ok                      ok            



So, no damages were detected while checking the hoses.




THERMOSTAT INSPECTION:
Here we learn to check the thermostat against manufacturers specification.


The thermostat manufacturers specification.= 86degree C.
Then i checked the thermostat by putting in boiling water along with the temperature reader. And kept till the thermostat open.

Thermostat opened at 92degree C.
Specs. 86degree C.
Thermostat was within the specs.? NO
Actions to bring thermostat within specs? We have to replace it with the right manufacturing specs. thermostat.



VISUAL CHECK OF RADIATOR PRESSURE CAP:

Q. Check the radiator cap for visible damage and report findings?
No visual damage.
Q.Check the sealing surfaces to ensure that they are in good order and report findings?
Pressure valve seal full of cracks , so replace the cap with the manufacturers specs.
Q.Locate the radiator cap vacuum valve is working correctly and report when it operates and what its purpose is?

vaccum valve working good , opens n closes at good time.



Then I,checked the cars radiator cap pressure and checked & determined  correct opening pressure..


At what Pressure should cap release at? 13psi
Whats pressure  did the cap release at ? 11 psi
Is this within the manufacturing specification? N/A
REPORT: Replace it with the same manufacturing  specs which is 13psi.

PRESSURE TEST THE COOLING SYSTEM:
Using a cooling system pressure tester, we checked the cooling system for leaks, to manufacturers specification on the radiator cap.

Manufacturer's pressure release specification? 13psi
Then
 check for the any leaks in the following areas like RADIATOR TANKS, radiator & heater hoses, heater core, cylinder head gasket , frost plugs, water pump ...etc. SO EVERYTING WAS ALL GOOD.


ACTIONS TO REPAIR LEAKS? Relace seals and gasket.





FAN BELT INSPECTION:

Here we checked the the condition, check it for cracking or deterioration, checked the sides for signs of slipping & checked fr signs of wear.

FAN BELT NUMBER:- 11A0965
Checked the "v" of the belt against the "v" of the pulley
Is the "v" correct for the vehicle? yes

Is the lenght of the belt correct for the vehicle? yes
Is belt serviceable? yes
If the belt is not suitable for further , action required? we have to replace fan belt with the same specs one.

WATER PUMP BEARING TEST:We learn to check the water pump pulley for damagesand signs of leakage, check the pulley shaft for any play and bearing for any noise by spining.

REPORT: Water pump is all in good  condition, there is no buzzing sound from the bearing or any leaks.

REFIT THE FAN BELT:HERE we refitted the fan belt using the given instruction.

Correct tension for the belt for our vehicle is 5mm.
And using a fan tension gauge I,determined the tension.

ADJUST THE DRIVE BELT:
 Here we learned to adjust the drive belt as all belts have some form of mechanical adjustments. So we folled the give manual loaded with all th steps during its adjust.

ELECTRICAL COOLING FAN:
And in last we checked the the operation of the electrical cooling fan by some simple test.

Here we located and disconnected the water/thermo switch connection, switch the ignition on.....if, the fan operates the fan is ok.

DOES THE FAN OPERTAES?? YES 












            













Thursday, 20 October 2011

TTEC4842- AUTOMOTIVE ENGINES (Cylinder head)

           ENGINES- CYLINDER HEAD



DATE:27/09/2011 to 7/10/2011







Removing Cylinder head :-  Here we learned how to remove & disconnect the cylinder head , using the service manual.











NOTE: 

  • Firstly we drain the engine coolant & dispose.
  • Then disconnect all cables , hoses , wires connected to cylinder head.
  • Disconnect the exhaust system and all other components that will be hinder the removal of cylinder head.
  • remove the rocker / cam cover.
  • Then we disconnected the cam drive, after putting timing marks .
  • Also we should note that the bolts r kept safely.
  • lose the cylinder head bolts using correct tools n procedure.
  • In last remove the cylinder head from the engine block.

Inspection of cylinder head: Here we measured the head face surface for warpage using straight edge and feeler gauge.

          our result:
              maximum warp                    actual warp           pass         fail         
                   specification.
                     .15                 Across      less then .038         yes.           -         
                     .15                length        less then .038        yes            -
                     .15               diagonal     less then .038        yes            -
  • we also checked the manifold and rocker cover for warpage if required.
  • we also checked the cylinder head for all other forms of damage as follow.
  • cracks.
  • broken edges.
  • broken or damaged fittings and brackets.
  • threads
  • corrosion.
  • core plugs.
  • camshaft bearings.
Valve guides: Then we inspect valve guides for damages.

                      Cylinder        1            2               3              4    
                      inlet             yes         yes             yes            yes
                      Exhaust       yes          yes            yes            yes
                                         ok            ok            ok             ok


Checking valve guide clearance by measurement:

Here we learned how to check the valve guide clearance by measurement.
  1. the guide should be clean in the bore.
  2. Then we use ball gauge or telescopic gauge to measure valve guide.
  • Expand gauge in guide until even pressure is felt , then we look in this for position.
  • Then remove gauge and measure across gauge with an external micrometer.
  • Then we recorded the readings in three positions in valve guide and then at 90 degree in the same positions.

Then we started taking readings fr 4 cylinder including (intake n exhaust.)  at position A & positionA at 90 degree to A, Postion B & Postion B at 90 degree to B, position C & position C at 90 degree at C.

Here is the result for aboves average.

                 
cylinder1       Cylinder2    Cylinder3    Cylinder4
                   IN     EX      IN      EX    IN      EX        IN   EX
Average    
6.02   6.02      6.03   6.04   6.02   6.01    6.01    6.02
reading:


VALVE STEM MEASUREMENT : H
ere we learned how to measure the valve stem measurement , using the telescopic gauge and how to measure the valve stem diameter in three places 1.At the top (large wear  area) position A  2.At the bottom (large wear area ) position C 3.In the middle ( least wear area) position B.


our average readings for 4 cylinder are :

                 cylinder1          cylinder2              cylinder3            cylinder4        
Average    IN      EX      IN          EX           IN        EX         IN          EX
Reading
: 5.96   5.97     5.96        5.96         5.96       5.97       5.97       5.97


VALVE STEM TO GUIDE CLEARANCE:
Here now we work out the valve stem to guide clearance by subtracting the average stem diameter away from the average valve guide inner diameter obtained from the previous measurements.
Stem to guide clearance Specification: 
Intake:- 0.025 to 0.06
Exhaust:- 0.030 to 0.065

                      cylinder1                 cylinder2              cylinder3                 cylinder4
clearance:    0.07   0.05               0.07      0.08         0.06      0.04             0.04      0.05                    

Pass:               -          yes               -            -               yes        yes              yes        yes
 Fail:              yes        -                  yes         yes            -             -                  -           -        

So, 3 valve were fail n rest were pass as they couldn't meet the specification and should be replace immediately.

CHECK VALVE CONDITION:
Here we learned visual inspection to check the valve condition. Following were the main areas we were ask to inspect .
  • Damage to the tip.
  • Damage or wear in collet grooves.
  • Pitting or erosion of valve stem.
  • Marks on stem which have sharp edges.
  • Signs of scuffing or seizure.
  • Cracks or erosion in fillet area.
  • Stretching of the stem.
  • Straightness of the stem.
  • Mechanical damage to the head, erosion or cupping.
All the above places were checked and inspected for all 8 valves in 4 cylinder.
Here we also measured the valve margin for IN & EX  for all 4 cylinder.
Result:


cylinder1               IN      RE-use     EX       RE-use  
valve Margin         .5        yes          0.8          yes


cylinder2              IN      RE-use     EX       RE-use
valve Margin    
    0.5       yes          0.9        yes


cylinder3               IN      RE-use     EX       RE-use
valve Margin    
    0.7        yes        0.8         yes


cylinder1               IN      RE-use     EX       RE-use
valve Margin
        0.7        yes         0.8         yes


 Valve seats- General Condition and Serviceability:
Here we visually inspected the :
  1. Seat width. 
  2. Seat angle.
  3. Surface finish - pitting , cracking erosion etc.
  4. Thickness of remaining material.
Everything was inspected and there was everything good, nothing to worry.


Refacing valves and valves seats:
Here we  get facility to recondition valves and seats .

our valves were as further: 
  • In good condition it is suitable to be refitted without further work.
  • And in poor condition they require replacement.
    In my result : 3 needs replacing.
  • In poor condition, to be reconditioned by the workshop.
  • In poor condition , to be reconditioned by outwork.

Inspection of valve springs.
Here we learn how to check valve spring is square, here we used a surface plate and an engineers set square to check squareness of valve spring.


Manufacturer's Specification: 1.6 (0.06)

our recorded results
: from 1 to 4 are EX and from 5 to 8 are IN.
  1. 0.508 mm                               pass
  2. 0.330 mm                               pass 
  3. 0.457 mm                               pass 
  4. 0.381 mm                               pass
  5. 0.038 mm                               pass
  6. 0.457 mm                               pass
  7. 0.610 mm                               pass
  8. 0.508 mm                               pass

Inspection of valve springs:
Here we checking free length of valve spring.

 Valve spring free length specification: Standard- 47.2
                                                                  Minimum- 45.1
                                                                  Maximum- 1.6
Note: All springs in set should have a free within 1.5 mm of each other.

Valve spring free length:
exhaust valve: frm 1 to 4
inlet valve: frm 5 to 8
  1. 46.7   mm                   pass
  2. 47.8   mm                    pass
  3. 47.8   mm                    pass
  4. 46.8   mm                    pass
  5. 46.5   mm                    pass
  6. 46.5   mm                    pass
  7. 46.7   mm                    pass
  8. 46.6   mm                    pass
Inspection of valve spring installed height and seat pressure:
Here we installed height must be measured with the retainer and keepers in place and with  the valve against the seat in closed position.
Note: The valve springs must be removed to carry out this measurement.

Spring installed height specification: 40mm

My valve spring installed height:
1 to 4 inlet valve
5 to 8 exhaust valve
  1. 43-3mm =   40mm                       pass
  2. 43.3-3mm= 40.3mm                    pass
  3. 43.4-3mm= 40.4mm                    pass
  4. 43.2-3mm= 40.2mm                    pass
  5. 43.6-3mm= 40.6mm                    pass
  6. 43.5-3mm=40.5mm                     pass
  7. 43.2-3mm=40.2mm                     pass
  8. 43.5-3mm=40.5mm                     pass
So, all was pass as was within specification.

Inspection of valve spring tension:
Here we learned how to check spring tension, Tension is checked on a valve spring pressure tester at the installed height obtained. This pressure is known as seat pressure and all springs should measure within 5 kg of each other.

Our result for valve spring seat pressure: 

Spring seat pressure specs=  20kg
          IN
  1. 14.9 kg
  2. 13.4 kg 
  3. 14.1 kg
  4. 14.8 kg

    EX
  5. 8.4 kg
  6. 14.4 kg
  7. 13.6 kg
  8. 12.8 kg
Here all above 8 springs were not under spec...that means the result was failed and we need to put the correct vsi to correct the seat pressure.

Rectify cylinder head faults-assembly of the valve springs:


AS the condition we noted all the springs were out of specification , so we can rectify  by the use of valve spring inserts(vsi washer) by inserting it under the springs.

After inserting the Shims (VSI's) , then valve spring tension will need to be checked with the VSI's included.

Shims size added (vsi's): 


frm 1 to 4 inlet & 5 to 8 exhaust.


  1. 1.85
  2. 2.57
  3. 2.04
  4. 1.78
  5. 3.6
  6. 1.66
  7. 1.97
  8. 2.53
So, we added different suitable sizes of shim to correct the valve spring in cylinder head.

Inspecting camshaft for wear and general condition.


Here we learned how to measure camshaft lobes and calculate the lift of each lobe, by using telescopic gauge we measured it by 2 positions A and B. 



  • INLET:-  (A) 41    -      (B) 33     =    (LIFT)  8.0
    cylinder 1.
  • EXHAUST:- (A) 41.38 -   (B) 33.2   = (LIFT) 8.1
  • INLET:- (A) 41.46 -     (B) 33.14    = (LIFT) 8.3
    cylinder 2
  • EXHAUST:- (A) 41.38 -  (B) 33.2  = (LIFT) 8.1
  • INLET- (A) 41.36  -  (B) 33.21   = (LIFT) 8.1
    cylinder3
  • EXHAUST- (A) 41.35 - (B) 33.2 = (LIFT) 8.1
  • INLET- (A) 41.40  -  (B) 33.1 = (LIFT) 8.3
    cylinder4
  • EXHAUST- (A) 41.3 -  (B) 33.0 = (LIFT) 8.3
All the inlet and exhaust cam lobes all have the same amount of lift. Camshaft is correct and serviceable.


Camshaft height specification INLET:- STD:-40.888 / MIN:-40.688
                                      EXHAUST:-STD:-40.889/ WEAR LIMIT:-40.689

Inspecting camshaft for wear general condition:

Here we learned to measured camshaft bearing journals for wear using external micrometer. The journals must be measured for both taper and ovality.

We measure at 1 & 2 for taper.
We measure at A & B for ovality.


OUR RESULT :


         EX                                 Front                                Middle                                  Rear
                                                  1                       2                              3                            4
Journal Ovality          26.49-26.46=.3      26.5-26.46=.16           26.48-26.47=0.1     26.46-26.45=.1
Journal Taper            26.45-26.46=.1      26.46-26.45=.1            26.48-26.46=.2      26.80-26.45=.35
                                               OK                      OK                              OK                       OK

        IN                               Front                                 Middle                                   Rear
                                               1                         2                               3                            4
Journal Ovality        26.44-26.44=0         26.46-26.45=.1            26.46-26.4=.1       26.44-26.44=0 
Journal Taper         26.45-26.44=.1        26.48-26.45=.1            26.46-26.45=.1      26.45-26.45=0
                                            OK                       OK                               OK                     OK


So the camshaft bearing ovality and taper are all good under specification.

Inspecting camshaft for wear and general condition:

Here we measured the camshaft run out using 'v' blocks and a dial test indicator.

RUNOUT
SPECIFICATION:-
0.01
ACTUAL:- 0.01

RUNOUT
SPECIFICATION:-0.03
ACTUAL:-0.01

All good under spec.camshaft can work properly .


CAMSHAFT AND CAMSHAFT BEARINGS ALL ARE IN GOOD CONDITION AND CAN BE USED WITHOUT ANY PROBLEM.




RECTIFY CYLINDER HEAD FAULTS - CAMSHAFT & BEARINGS CONTINUED:




Firstly I checked the camshaft bearing oil clearance (using plasticgauge):
  1. I check for the camshaft bearing and journal are cleaned.
  2. Then I postioned a strip of "plasticgauge" on the top of the journal (in an axial direction)
  3. Place the camshaft caps in position and tighte to specified torque.
  4. And in last I removed the cap and measured the oil clearance.
our result was as follow.

OIL CLEARANCE:
                                    journal 1       journal 2        journal 3           journal 4          journal 5 
OIL CLEARANCE    0.076              0.076              0.076                  0.076               0.076




The result here was also all good .




ASSEMBLE THE CYLINDER HEAD:


Then we assembled the cylinder head back again , firstly i refitted the valves again in same oder in which they were removed. before sliding valves into guides ensure that.

  1. The valve and seat are clean
  2. The valve stem and valve seat are lubricated with clean engine oil.
  3. Be extremely careful when pushing valve stem through stem seal that no damage occurs to the seal.
  4. we also ensure that all valves spring shims are fitted correctly.
  5. valve stem seals are fitted the corrrectly.
  6. Valve springs are fitted in correct way .
  7. Then we ensure the retainer cotter are cleaned and installed correctly, we put greases on the cotter to help placing them.
  8. Last point we should alwayz remember that use the correct valve spring compreesor when assembling all valves and springs etc.
NOTE: wear eye protection.

Assemble the cylinder head- FITTING CAMSHAFT AND ROCKERS:

FOLLOW THE MANUFACTURERS SPECIFICATION:-

  1. Ensure all parts are clean.
  2. RE-assemble the rocker gear and shafts with clean engine oil.
  3. oil the camshaft bearing surfaces.
  4. carefully fit camshaft in cylinder head.
  5. Fit rocker assembly (ensure all rocker adjusting screws are backed off). Torque all bolts to manufacturers specification.
  6. Ensure camshaft turns.
  7. Measure camshaft end play and ensure it meets manufacturers specification.


End-float reading-    0.06
End-float specification:- 0.07


WE PLACED THE METER TO FIND THE SPECIFICATION AND FOUND THE RESULT UNDER SPECIFICATION , WHICH MEANS EVERYTING IS ALL GOOD.




Cylinder head rectification report:

Report:

1.cylinder head condition:Requires repair.
  • Type of fault:Missing bolts & distributor bairing cap.
  • Explain fault:Just need to put back the 2 missing bolts and distributor bairing cap.
  • Type of rectification:
    BUY new from market and put them back.


2. VALVE GUIDE:
      No action required.

3.VALVE SPRING:
    Repair or Replace.

  • Explain fault:
    Spring were not in spec.for there spring seat pressure.
  • Type of rectification:
    Can be repair or replace (repair by putting shem) to make that within specification.

4.Core plug condition:
   
No Action Required.



5. Threads, studs and threaded holes:
    No Action Required.


6.Camshaft Condition:
   No Action Required.


7.Camshaft Bearing:
  No Action Required.



*And also we should remember the name of the gaskets and seals which are required to complete this job....some of them are -> cylinder head gasket , oil gasket , exhaust manifold gasket ,thermostat manifold gasket.



Now we got practical exercise , using a four stroke engine: 


  1. Here we were asked to create a valve timing diagram.
  2. Then determine the piston travel in relationship to crankshaft rotation.
  3. Calculate engine cubic capacity.
  4. Calculate compression ratio.
my result :


INLET OPENING :       15degree           (BTDC)
INLET CLOSING:        
65degree           (ABDC)

EXHAUST OPENING:  65degree           (BBDC)
EXHAUST CLOSING:    5degree            (ATDC)

*Then we draw a valve timing diagram using the above result.



Piston travel in relationship to crankshaft rotation:


1. Starting at TCD , using the degree plate and vernier caliper, then we noted  the piston travel at each of the degree positions.NOTE : Measurement are taken from the upper cylinder block face to the top of the piston.

our result:   
                 Crank postion angle         Distance to piston (DEGREE)
                         T.D.C                                          0
                     15degree A.T.D.C                          2
                     30degree A.T.D.C                        4.5
                     45degree A.T.D.C                        8.5
                     60degree A.T.D.C                         15
                     75degree A.T.D.C                         22
                     90degree A.T.D.C                         28
                    105degree A.T.D.C                        33
                    120degree A.T.D.C                        37.5
                    135degree A.T.D.C                        42
                    150degree A.T.D.C                        44.5
                    165degree A.T.D.C                        46
                    180degree A.T.D.C                        46




2. Using the above readings , we produce a graph of piston travel against crank travel.
3.After completing our graph , weather the piston has traveled half the           stroke when the crankshaft has rotated90 degree.
4.Using the valve timing data, then we plotted the valve opening and closing points on the graph.














































































           



























Tuesday, 27 September 2011

TTEC4843 :- FUELS AND FUELS SYSTEM

Date:-19/9/2011


IDLE SPEED DEVICE:
In this task we tested the idle speed device.



  • First thing was asked to check which type of cold or fast idle speed control does our vehicle use?- our was "stepper motor".
  • And the base idle speed is adjusted here by ECU. 
  • Here the cold / fast idle speed is control activated by "ECU".
  • The correct procedure for checking this control is- ,firstly check the resistance winding test, then test duty cycle and frequency (spec 9-14v) and connect the bridging wire on terminal TE1 and E1 to check control.
  • our result for the resistance in winding: used multimeter n used to find btw two pins.
    RSO-EO1=33 OHMS
    RSC-EO1=24 OHMS
  • Then we used the digital meter to measure the duty cycle and frequency that operates the IACV- OUR RESULT WAS ... !DUTY:-Open 51% & close 49% 
    Frequency:- 244(open) & 244 (close) hz
Report: Our engine was in all good condition , the ECU adjust the base ideal speed where as idle speed control is determined by engine temperature and the time engine is cold means more air flow. Then we checked the continuity, we measured the resistance windings by keeping the black & red probe on RSO (open) & RSC (close)..which was 33 ohms and 24 ohms. Then had our duty test which was 51% & frequency came to be 244hz , that showed us how many times it turns on/off.


Checking Fuel Lines:
Firstly we checked the condition of fuel hoses, :- firstly had a visual check on the fuels lines on the vehicle, then checked for any cracks or perished rubber hoses, are the lines tight,check for any leaks ,check if its lose or bend.
RESULT:- PASS,.... OUR VISUAL CHECK ON FUEL HOSES IS ALL GOOD , THERE IS NO LEAKS AND EVERYTHING IS TIGHT & GOOD CONDITION.


CHECKING FUEL PUMP(fuel injection high pressure):
It is an electrical pump which can be mounted either inside or outside the fuel tank.
Here we learned how to work with the high pressure fuel. Firstly we use manual book to follow the procedure..as follow.
  • we check the running pressure at idle.
  • we also check the running pressure under full engine load.
  • Then check the maximum output pressure of the fuel pump
  • And in last check the residual line pressure.

SAFETY PRECAUTION TO BE OBSERVED: Check for the rsidual pressure when car is off, decrease the pressure by disconnecting the fuel relay,while the car is on.

MANUFACTURER'S SPECIFICATION: 
Ignition on: 265-305kpa
jumper disconnected: 206-255kpa
ignition off:147kpa

OUR TEST RESULT:
Pressure at idle:270kpa
WOT pressure:340kpa
Max Pressure:560kpa
Residual Pressure:255kpa

All, good the pressure were within specification.So, all good.


CHECKING FUEL PUMP FLOW:
After the pressure checks ,we can check the fuel flow through the system. Firstly after droping the residual line pressure, remove the pressure gauge from the fuel system. Then with the help of the manufacturer we'll check the fuel flow *after the pressure regulator for normal pump & *before the regulator for maximum pump flow.


Then ,it shows us the flow rate in minute for the pressure regulator for the fuel pump.

MANUFACTURER'S SPEC: 195-MAX FLOW & 135-NORMAL FLOW
OUR TEST RESULT:
                                                                              NORMAL
10SEC-540ML(.54L)                                        10SEC- .39L
60SEC-3240ML(3.24L)                                      60SEC- 2.34L
1HOUR-194400ML(194.4L)                               1HOUR- 140.4L


LOCATE AND IDENTIFY SELF TEST CODES AND ISOLATE CAUSE.

In this we learned how to identify and do self test code.
The vehicle we started with was Toyota 4AFE , flashing light on the dash board is the method used to display the diagnostic codes.

SPECIAL TOOLS AND EQUIPMENTS WE USED : jumper wire , scan tools to check the faulty codes and scope to check wave pattern.

*Firstly we bridge the wire from TE1 TO E1 terminals and then count the number of blinks of engine light on the car dash board.

The fault detected from us was 22,31,24
22- water temp.circuit (coolant sensor)
31-vacuum sensor circuit(MAP).
24-Intake air temp.sensor.

*THEN ,we rectified the faults , firstly we checked the connection on sensors.
  • MAP sensor- were checked using vacuum pump and voltage regulator
  • Coolant sensor temp.switch- checked by using heat gun water and thermometer.
  • Air temp.sensor - heat with heat gun & check temp.with leaser sensor.

FINALLY:
The faults were solved with d help of the blinking light we recognized the above codes...and started finding the problem.in there , All the above codes were solved by reconnecting the circuits or wire, which were unplugged, And during in between the lights use to confuse us by blinking differently ,for this after every fault solved we should take the key off and start after little while.

SERVICE AN AIR CLEANER:
 It is really important that the air filter should be clean and working properly .It is not filtering the air entering  the engine dirt and particles as it will cause damage to the engine, and if itz blocked then it gonna affect the emission and fuel consumption.
Firstly we removed the air filter and and checked for damage or excessive dirt or any oil contamination to the filter element.
*all was good,it passed the inspection
*condition still all good and can run till the next service without any problem.

PCV VALVE:
we performed on the testing of pcv valve, first thing we did  was ,we clamp the rubber hose(using a brake hose clamp) going to the pcv valve does the idle change?YES(SO,PASSED)

*Then we checked for clicking sound which can be checked by listening,so as to knew that the plunger can move freely? yes

AS DURING CLAMPING THE RUBBER HOSE THERE WAS AN IDLE  SOUND CHANGE , WHICH SHOWS PCV IS IN GOOD CONDITION. SO, NO FAULTS AND ALSO THERE WAS CLICKING SOUND WHICH MEANT THE PLUNGER IS MOVING FREELY.
ALL GOOD.


VACUUM OPERATED EGR VALVE:
Today we tested vacuum operated EGR valve.


Record the EGR test result:

  • Did the engine idle smoothly at normal operating temperature?-YES
  • Did the idle speed change with vacuum applied to the EGR valve? -YES
  • Did the valve show any signs of air leaks through the stem seal? -NO
  • Is the EGR system working to specification? -YES


OUR RESULT:
No service require yet, all working good as manifold doesn't suck gases on idle and an crusing gases started being vacuum into NOX area in manifold.

The EGR is used to control/reduce NOX emission by introducing exhaust gas back into inlet ,there by reducing the combustion temperature.

ADJUSTMENTS AND EMISSIONS:
 In this we learned about adjustments and emission, firstly we tested a vehicle with carburetor and without a catalyic converter and then recorded the result.


  • Firstly we bring the engine to operating temperature.
  • Then we prepared the infra-red gas analyzer as required.
  • Then calibrate the gas analyzer gauges.
  • After which we set it to zero and adjust the span settings (analogue gauges).
  • Fitted the sampler hose into the exhaust of the vehicle.
  • In last we took the exhaust gas sample.
 And our result was:


ACTUAL BEFORE ADJUSTMENT                                   INDUSTRY STANDARD
H.C. - 159 ppm                                                                       H.C.  - 50 to 500 ppm
C.O. -0.528 %                                                                         C.O. - 0.5 to 1.5 %
CO2 - 14.24 %                                                                         CO2 - 13 TO 14.5 %
O2 - 0.18%                                                                               O2 - 0to 2.0 %


RESULT : YES, all good reading within specification.


EFI VEHICLE TEST:


ACTUAL                                                 INDUSTRY STANDARD

H.C. - 178 ppm                                           H.C.  - 50 to 500 ppm
C.O. -0.824 %                                           C.O. - 0.5 to 1.5 %
CO2 - 13.84 %                                          CO2 - 13 TO 14.5 %
O2 - 1.14%                                                  O2 - 0to 2.0 %


*THE RESULT WAS ALL GOOD.
The difference we noticed in two sets of reading as follow:

  • HC it alwayz should be lower , as if its high then the specification it refer that the fuel is not buring properly.
  • CO  is also same as HC , they may  too cause rich mix 
  • if CO2 is high , it means engine burns efficiently , however if O2 is high , it means the mix is  too lean and its not good.

REMOVAL & REPLACEMENT OF DIESEL FUEL INJECTORS:

We learned how to check diesel injectors and inspect.

we firstly removed the diesel fuel injectors, then using harbridge test master machine we tested each injector.Then putting each injector one by one on the machine check for the spray pattern.And if there is any problems with them we set our machine to 18 psi, then pumped the injectors and we could not meet the specification as the spec fr ATM WAS 118 to 125 bt the result was all out. So need to change all four injector as they couldnt meet the specification n have not gud spray pattern evn thr was leakage.


BLEED AIR FROM A DIESEL INJECTION SYSTEM:-
HERE WE LEARN HOW TO BLEED THE AIR FROM DIESEL INJECTION SYSTEM.Remove the fuel pump filter to bleed from the hand , then loose the fuel line and disconnect it from the fuel distributor, then put the fuel filter back and start pumping the filter from this the fuel will start comiing out from fuel line , first it will not be soo flued because of air pressure bubles inside but once it get fluent, put the fuel line back .start the engine and checked., all good.


Decribe the location of the air bleed screw on d engine??
ANS- it was on the fuel pump top close to the fuel return.

TESTING ELECTRONIC SHUT OFF VALVE:-
 
We tested the electronic shut off valve with the ignition on, then we have to use the multimeter to test the voltage coming from ignition switch to the electronic shut off solenoid.

voltage-
12.4 v
Resistance of solenoid winding- 9.5 ohms


 OPERATION O SOLENOID:
Solenoid is not NA, but we checked the one which is attached on the engine diesel pump. So, when we connect the wire of solenoid then the clicking sound indicates the solenoid working properly And our result 12.4v shows that the solenoid is working as voltage is detected & the resistance confirms us the coil is working properly.

DIESEL INJECTOR PUMP TIMING:
HERE WE LEARNED HOW TO TIME A DIESEL INJECTOR PUMP.
DTI-Remove the cam belt and rotate the pulleys to TDC and reset them to there points , put the belt back and tight the pulleys back & tight the belt , taking care to have the timing makes aligner and  engine on TDC firing number one.
SPILL TIMING- done all good, jst have to remove the full injector lines , and adjust it.

Special tools- DTI gauge, socket tools , allen key /hen key tools.


TESTING GLOW PLUGS:

We tested the glow plugs.
                    glow plug1        glow plug2         glow plug 3         glow plug4
current draw         8amps                    8amps                    8amps                       8amps


colour of glow       
turns red                  turns red               turns red                 turns red
plug tip. 



RESULT: Firstly we removed the 4 glow plugs and earth them to the ground to check weather they are working or not , we checked 4 of them all were pass as the top of them turns to be red.As they turn red that means there are working properly and there wont be any trouble.this shows us that the plugs are useable and cn be charged.



















Monday, 26 September 2011

TTEC4843 :- FUELS AND FUELS SYSTEM

                TTEC4843:- EFI OFF CAR

CLEANING INJECTORS:-
In this we learned how to check and clean electronic fuel injectors.

  • Their were 4 injectors .
  • Then we listened each injector with stethoscope while the engine is running..all were audible,so all good.

*Then we expose the wiring into the back of the injector plug, we take one injector at a time  and connect an LED checker ,then record if the light flashes.
  • All 4 LED indicates the pulse present.
*Now, checked the injector operation by the engine speed.
  •  yes , there was a 1000rpm drop during a single disconnect of injector.
*Also checked the resistence of each injector winding with the ignition off.
  • all 4 winding resistance was 15.4 ohms. 
  • So all good as under specification ( 12-16ohm)
*off car injector testing
  • we performed it on all the 4 injectors we fitted them into the testing machine and checked for the injectors.
  • check if  all fitting are secure before mounting them in the test machine.
*specification:-


  • injector leakage:- 1drip per minute.
  • injector flow rate 220cc per minute flow rate at 3.0 hz.
All 4 injector need intention=spray pattern flow rate not good fr all 4 injectors and where as injector leakage was also there.
*clean them or replace.

Important Note: 
  • when replacing fuel injector do not forget to, replace all top "o" rings and lower "o" rings.
  • Ensure injector seals and "o" rings are lubricated and injectors correctly located.
  • And all fuels lines and connections  are correctly located without leaks.

AIR FLOW METER RESISTANCE TEST - FUEL INJECTION DIAGNOSIS:-

In todays task we checked the resistance on the air flow meter using ohms meter by checking the potentiometer circuits and determine the air flow sensor condition by comparing the result with the manufacturing specification.
  • first thing we did was tested E1-FC closed had reading of infinty
  • E1-FC open  0.2ohms
And it shows if the fuel pump relay is effected on pump operation with high resistance across the two terminals, this will not give right measurement and amount of fuel.
*As higher is the resistance so lower will be the voltage and fuel pump relay wont get enough current to open the fuel pump.

*AALL OTHER SENSORS HAS BEEN DISCUSED IN REPORT

AIR FLOW/MASS SENSOR TESTING:
  • we started by looking for the air flow sensor on the outside of air cleaner.
  • it is bolted to the air cleaner with the ducting connected to the throttle body.
  • it could be in following shape:L type moving vane,hot wire ,sliding piston(mazda,ford), Karman voltex air pulse (mitsubishi) etc.
*the one we detected was L type moving vane.
*we need to have multikmeter ,heat gun and heat reader laser gun.
Acc. to the stated procedure the sensor could not meets the specification and can not be repaired

AIR TEMPERATURE SENSOR:We tested the air temperature sensor and using multimeter check sensor resistance.

Terminal no.             Tempersture               Reading                      Specification  
E2-THA                       20*C                           2130                            2000-3000 ohm

                                     60*C                           120                                 400-700  ohm






THROTTLE POSITION SENSOR (LINEAR TYPE): LINEAR TYPE IS THE ONE WHICH SENDS READING EVEN WHEN THE BUTTERFLY IS MOVING FROM  CLOSE TO OPEN OR OPEN TO CLOSE

  • We check that the throttle leakage move smoothly.
  • Check for the vaccum with your fingers at N port while engine start.
  •  inspect throttle position sensor.
  • inspect throttle body,throttle body valve and clean throttle body.
When we inspected the throttle position sensor, firstly discoonect the sensor, insert the feeler gauge   between the throttle stop screw and stop lever and ohm meter measure the resistance between each terminal.



multimeter:positive:-voltage in  ,                         negative:- fully throttle

TB fully open = 0V
TB closed =infinity

Now multimeter 
positive or red lead=Voltage in.        black lead or negative = on idle position 

TB fully closed =0V
TB open =infinity

THROTTLE BODY CLEANING:

Throttle body gets dirty from engine gas recirculation
(EGR), there is a small hose that spends post combustion gases into the intake.The post combustion gas dirties the throttle body and rest of the intake manifold,so when we clean throttle body oil  and dirt then it promotes engine effeciency.

TYPES OF AIR MASS SENSOR:
  • L jetronic type air flow sensor.
  • LH jetronic hot wire type sensor .
  • D jetronic manifold absolute pressure sensor.
  • karman vortex air flow sensor.